Drive-on (knock-on) rail anchors and Spring type (wrench-on) rail
anchor
Rail anchors made in one-piece construction from spring steel are designed to
fasten the rail tight on the base of the rail to prevent the rail
from longitudinal movements, i.e. the “ creeping” of the rail,
caused by changing temperature, grades, traffic patterns, and
braking action of trains.
Rail anchors are applied to the rail base directly and lodge up
against the tie. Rail anchors provide a large bearing surface
against rail base and rail tie, preventing cutting and wear, and
eventually to prolong the working life of the rail ties. Anchors
are made for a specific rail weight and base width, which can be
classified into two types: the Drive-on rail anchors and Spring type rail anchor.
Application Rules of Rail Anchors
How to use the rail anchors? There are general rules on the
application of rail anchors:
- Rail anchors should be on the gage side of the rail base against
the same tie face on opposite rails.
- Rail anchors have to hold the rail base tightly and firmly and have
full bearing against rail tie face.
- A new rail anchor and a rail tie will be needed when the bearing of
rail anchor against the tie has been disturbed.
- Anchors shall not be moved by driving them along the rail.
- The rail ties should be kept straightened when the anchors are
applied.
Locations of Rail Anchors:
Usually, rail anchors are used in the following locations of rail
ways.
When anchors are used, taking a 39 foot rail for example, 8 rail
anchors is usually commended to be used, as shown in the following
diagram. While the steep grades increased, the number of the
anchors may be increased.
rail anchor loaction
Recommended Minimun Anchoring Pattern for 39-foot Rails.
At open beck bridges. Anchors are used on track approaching open
deck bridges, every third tie should be box-anchored for at least
two rail lengths off each end of the bridge.
At rail crossings. As rail crossings where anchors are used, every
third tie should be box anchored for at least two rail lengths in
all directions from the crossing.
Rail turnouts. Anchors is optional used in turnouts. When anchors
are used in the turnouts, it is helpful to correct the geometry
problems.
Types of rail anchors:
1. Rail anchors are always used in rails such as 50kg, 85kg, UIC54,
UIC60, 90/91lb, 115RE, 136RE, just to name a few. We can produce T
or V-shaped rail anchors as well as other types according to
clients’ requirements, by forging or casting.
rail anchor Type
Material
Brand | Zhongyue |
Name | rail anchor |
Type | used in 50Kg, 85Kg,90/91LB, 115RE /136RE ,UIC54 & UIC60 rail |
Or the type by customers’ drawings |
Material | 60Si2MnA | 45# | QT500-7 |
Chemical composition(%) | C:0.56-0.64, | C:0.42-0.50, | C:3.60-3.80, |
Mn:0.60-0.90, | Mn:0.50-0.80, | Mn:≤0.6, |
Si:1.60-2.00, | Si:0.17-0.37, | Si:2.50-2.90, |
Cr:≤0.35, | Cr:≤0.25, | |
P:≤0.03, | P:≤0.035, | P:≤0.08, |
S:≤0.03 | S:≤0.035 | S:≤0.025 |
Surface | plain (oiled),color painting |
Standard refers |
|
2. Generally speaking, based on our former production experience,
most common material for rail anchor production is 60Si2MnA, which
is often used for rails such as 50kg, 70lb, 80lb, 90/91lb and so
on.
Type Material Weight(g/pc)
50Kg 60Si2MnA 800
70LB 60Si2MnA 800
85LB 60Si2MnA 800
90/91LB 60Si2MnA 800
3. Rail anchors for Russia market : high grade ductile iron
castings
Russian rail anchor is often used in railways by casting, which is
made from material of QT400-15. All related mechanical properties
of it are strictly following with the standard of TOCT 7293-85.